DIY SPOOKY CHRISTMAS STOCKINGS

Whenever it comes to the holidays, I’m all about putting new spins on things. Instead of kelly green, let’s opt for emerald. Swap Crayola red for ruby. Cartoon snowflakes & creepy Santa prints? I’ll take metallics & faux fur ANY day.

But when we’re talking about infusing tradition with our own taste, there’s always room (& by room I mean a need) for some spookalicious action as well. Which is why last year as K & I pined over the classic struggle of how to decorate an apartment ((not to mention, with two devious kittens in the mix, too)), we hit a road block. 

UNTIL – the solution came…

Stockings! Specifically, made out of the spooktacularly festive fabric we recently saw at one of our fave local horror stores.

So from there, the creation began. Never had I thought about sewing stockings, but hey, it’s just a giant sock, right? How hard could it really be? And I have to say, it felt like they turned out pretttty freaking well.

So kiss the tired, ’80s mantles goodbye! And say hello to the creepy-cute holiday upgrade you never knew you needed…

// WHAT YOU NEED //

+ 1 sheet, tissue paper

+ 1/2 yard, spooky outer fabric

+ 1/2 yard, lining fabric (minky or a short-piled faux fur looks best IMO!)

+ A scrap of ribbon or other thick fabric (for the hanger)

+ A needle & heavy-duty thread

+ Puff paint pens (optional)

// STEPS //

++ Draw your main stocking shape onto a piece of tissue paper. I used the measurements below, but feel free to customize for whatever size you like/need!

++ Cut out your stocking pattern & fold the outer fabric in half such that the right-sides are facing IN; & the lining fabric such that the right-sides are facing OUT (a little confusing, but it’ll all make sense in the end). 

++ Pin the pattern onto your outer fabric & cut, so that you have two, identical stocking shapes. Repeat for the lining fabric.

++ Take your two pieces of outer fabric & stack them with the right-sides still facing IN. Then, take your two pieces of lining fabric (right-sides still facing OUT) & sandwich them around the outer fabrics. Pin the fabric stack together – which should look like it’s totally inside out.

++ Sew around the perimeter of the stocking using a zig-zag stitch, leaving about 1/4 inch of seam allowance. 

++ Flip the stocking right-side out (so the outer fabrics should now be on the outside with lining fabrics on the inside) & fold the top down to expose however much of the fuzzy fabric you’d like.

++ Cut & fold your ribbon/thick fabric into a sturdy loop, then stitch it onto the top corner of the stocking to create a hanger.

++ And finally, if you want to puff-paint names onto each for an extra personal touch, feel free! Or else just hang & admire a darkly festive job well done.

What are some of your favorite twists on tradition?

xxAA

DIY STEAMPUNK-CHIC FAUX FUR SCARF

JON SNOW BUT MAKE IT FASHION

That’s the main idea I ran with for this latest accessory fresh off the line (read: my dining room table) for winter. It’s part scarf, part shawl – with a hint of steampunk, meets early 2000s Tripp pants, meets…those IKEA rug capes that Jon & his Night’s Watch bros donned over at The Wall in Game of Thrones.

Perhaps a combo you never would have dreamed, but here we are! And it’s amazing.

Much like our chain cape necklaces, I’m all about the subtle, industrial-chic accessories. Sure, jewelry is cool, but can it turn plain shirts, sweaters & more into whole new statement pieces? Not so much.

So this is one that truly delivers.

Another little confession time tidbit for ya: despite trying & trying (& trying & trying…), I’m part of the 0.1% who never could fully get onboard with the whole GOT obsession. BLASPHEMY some might say. Believe me, I’ve heard it. Although hype wars aside, there’s no denying some of the fashion was pretty on point.

Especially those incredibly repurposed, super thrifty, IKEA rug capes.

Snaps for you, HBO.

// WHAT YOU NEED //

+ 1/3 yard of faux fur fabric

+ 1/3 yard of lining fabric (poly-satin works great)

+ Two pieces of 1/2” grommet/eyelet tape, each cut 18 inches long (adjusted to your own torso measurements, if needed)

+ Two 1/2” swivel hooks & one matching D-ring

+ One 3” piece of black elastic (1/2” wide)

+ Needle & heavy-duty thread

+ Sewing pins

// STEPS //

++ Cut your faux fur into a strip approximately 40 inches long by 6.5 inches wide (NOTE: unless you’re in the market for a fur storm, push the pile to the sides as you make small snips down the middle of the split to minimize shedding).

++ Cut/round off the top corners of the fur so its final shape matches the graphic below (adjusting to your own measurements, if needed).

((hopefully my precious little graphic isn’t too confusing!))

++ Flip the fur over so that the wrong side is facing up. Lay the lining fabric on top & begin pinning it to the fur, leaving one to two extra inches of lining sticking out past the edges. 

++ Trim off any excess lining fabric beyond those one to two extra inches, remove the pins & flip both of your fabric pieces over so that the right sides are facing each other. 

++ Re-pin the two fabrics together & make sure to keep all faux fur strands around the edges tucked inside. That way, we can fluff it all out later, as opposed to it getting stuck inside the stitches.

++ Fold the strip of elastic in half, stick it through the D-ring & fold in half again. You should now have four layers total with the D-ring sandwiched in the middle.

++ Pin the elastic/D-ring into place (again, check out the graphic) so that it will stick out of the back once we turn the finished scarf right-side out.

++ Use a sewing machine to sew along the two long edges, leaving the curved ends un-sewn for now (this helps prevent the lining from sliding around & getting mind-numbingly messed up). Remember to keep the fur strands tucked in as you go.

++ Sew along the edge of one of the rounded ends to close it up, then flip the scarf right-side out. Ensure all looks good & if so, carefully hand-stitch the other end closed.

++ Fold one piece of the grommet tape around the swivel hook and straight stitch it into place. Clip the swivel hook onto the D-ring & put on the scarf. Follow the grommet tape (making sure it doesn’t twist) to the outer edge of one of the scarf’s ends & pin it wherever feels most comfortable to you. 

++ Straight stitch (or hand-stitch) the tape into place & repeat for the other grommet tape/swivel hook set on the other side.

Pretty please share if there’s something crazy you’ve ever repurposed into gold!

And in the meantime – stay warm, frost kittens…

xxAA

DIY CHAIN CAPE NECKLACE

Yep, you heard me right! A chain. cape. necklace.

Do tell?

Honestly, I’m still not sure if that’s technically the best way to describe it. But basically, it’s a choker & two upper arm bands attached via chain. Like magician x medieval knight, or superhero x tetherball pole – super fun, right?!

When it comes to metal, typically you think jewelry, purses, maybe a Spencer’s wallet circa 2006 if we dare flash back that far. Although the truth is, chain accessories can go SO much further than that. And not to mention, look super chic while at it.

Think paired with sleeveless top or dress to make make for a Cleopatra-inspired situation, or added to your favorite fall/winter staples for a more subtle, industrial-glam touch. Either way, there’s no denying it creates an interesting vibe to look at – plus, turns any tired-feeling outfit totally on its head.

So what more could ya want?

// WHAT YOU NEED //

+ Black elastic (1/2 inch wide)

+ 4 jump rings (15 mm)

+ Your choice of sturdy fabric for the choker

+ Curb chain (60 inches long)

+ One hook & eye closure

+ Needle & heavy-duty thread

+ Sewing pins

// STEPS //

THE ARM BANDS

++ Measure your upper arm & cut four strips of black elastic to length + one extra inch.

++ Cut two additional pieces of black elastic approximately 2 inches long.

++ Take the four elastic pieces you cut for the upper arm bands & pin the ends of each piece around one jump ring to create four individual bands.

++ Stack two of the individual bands so that the jump rings line up & pin one of the 2-inch elastic pieces around the two jump rings to connect them. Do the same for the other set.

++ Use a zig-zag stitch to secure each folded over section of elastic to create two finished upper arm bands.

THE CHOKER

++ Measure your neck & cut a 2.5 inch-wide strip of your choker fabric to length + one extra inch for the seam allowance.

++ Fold your strip of fabric in half the long way (AKA hot dog style) so that the right sides are together & pin it.

++ Sew a straight stitch across the width of the fabric at each end & flip the strip right sides out.

++ Make sure all of the extra fabric is tucked in & sew a straight topstitch along the right side of the fabric to create a clean-edged choker band. Then, topstitch the other side to finish it off.

++ Finally, hand-sew a hook & eye to each end & double-check that it still fits your neck.

TO FINISH

++ Cut your curb chain in half to make two 30-inch pieces & hand-sew one end of one chain to the inside of the choker left of the hook & eye, then one end of the other chain to the right of the hook & eye.

++ Take the other ends of each chain and hand-sew one to each arm band. Done & done!

xxAA

DIY PUMPKITTEN SQUAD

Mmm, there’s nothing like prancing around a pumpkin patch IN 90-DEGREE WEATHER.

Ugh. Fall, it’s normally not hard to love you, so why. WHY???

Anyway – it’s crazy to think that Halloween is already just nine short days away. And if that also means you’re running out of excuses to continue putting off that annual love/hate relationship you have with carving pumpkins, then do we have a fix for you!

Now, don’t get me wrong. Pumpkin carving is cool. I mean, I never actually did it for real for real until just a few years ago, but at the same time…there’s no denying the mess. Or the smell. Or how it feels like they’ve already rotted before you even ~really~ have time to enjoy them. 

So from all of that we came up with a solution. Something cuter, cleaner & that can still be just as creepy if you get the beady eyes right: PUMPKITTENS!

A feline fierce take on classic jack-o-lantern vibes, mini pumpkitten squads are the answer to our pleas of ornamented squash vitality. Since we’re painting instead of cutting into the pumpkins, they’re guaranteed to last loads longer. PLUS, unless you’re a regular Michael Myers with knives, this method provides way more creative control with just as much customizable potential, too!

Seriously, it wasn’t until just YESTERDAY that we finally threw away the lone survivor of last year’s crop. So especially if you’re one to consider Halloween decor as just decor, then this project is totally up your alley.

// WHAT YOU NEED //

+ Mini pumpkins

+ All-purpose craft paint (black & green)

+ A very thin paintbrush 

+ A pencil 

+ Black pipe cleaners (2 per pumpkin; cut into 3.5-inch pieces)

+ Flexible black craft/jewelry wire (6 per pumpkin; cut into 1.5- to 2-inch pieces)

// STEPS //

++ Use the pencil to lightly sketch an outline of the face, including the eyes, nose & mouth.

++ With an exceptionally steady hand, first paint the green portion of the eyes. Let dry & apply a second coat.

++ Wash your brush & then paint the black portion of the eyes and outline the nose/mouth. Let dry.

++ Bend your pipe cleaners into the shape of a cat’s ear & stick them into the top of the pumpkin in an applicable, ear-like position.

++ Finally, stick half of the wire pieces on each side of the mouth & fan them out to resemble whiskers.

(NOTE: if your pumpkin(s) are unusually hard, you might need to use a toothpick, psycho ice pick or any other sharpish object to make a small, prelim puncture before sticking your pipe cleaners and/or wire into place)

And there you have it! Adorably festive (& somewhat everlasting) pumpkittens ready to usher in yet another fabulously spooky season.

Let us know how they turn out for you!

xxAA

FALL’S MOST UNEXPECTED ACCESSORY: DIY GLAM BANDANAS

Ah, bandanas. Something you probably haven’t thought about since that godawful country western-themed dance in middle school – unless you’re a roadie for The Grateful Dead.

BUT now that fall temps are starting to arrive and we can actually stand to wear something around our necks without dripping in sweat, we’re proud to introduce: the glam-dana!

A great way to transition into fall, this edgy twist on the classic kerchief might just be our new obsession. And for good reason! After all…

–Basic bandanas are cheap as hell. Like, 99 cents cheap.

–They come in a surprisingly huge array of colors & prints.

–The fabric is super easy to work with (& also wash).

–You can style them in so many different ways (I’m talking from tanks to turtlenecks).

–AND they’re totally customizable to whatever vibe you’re feeling – and/or supplies you have laying around. 

Seriously, beads, trim, studs, spikes, buttons, sequins – even dye or paint if you really want to get creative. It’s one of those projects that you can invest however much (or little) time you’d like, plus truly make all your own.

So let’s dive in!

// WHAT YOU NEED //

+ A bandana

+ Bead needle & thread (double layered & knotted at the end)

+ Regular needle & thread (double layered & knotted at the end)

+ Beads (I used seed)

+ Fringe

+ Your choice of chain & studs (or whatever else you want to use for embellishment)

// STEPS //

++ First things first: rescue that bandana with an iron. You won’t get ~all~ of the creases out, but give it a valiant effort.

++ Fold the bandana in half diagonally and choose which side you want to be your main (luckily we only have to decorate the half that’s going to show).

BEADING

++ If you want to bead, that’s the first detail you should knock out (if not, just skip to the next section).

++ Once you figure out which areas you want to accent with beads, take your threaded bead needle and make your first stitch. Pull the needle though the fabric so the knot is on the non-visible side and sew a few tiny stitches, just to secure the thread. 

++ Add your beads two to three at a time onto the needle and pull them all the way down the thread so that they’re touching the fabric. Lay them down along where you want them to sit, and pull the needle down through the fabric right after the last bead to sew them into place.

++ Pull your needle back up about two to three bead’s length away from the last sewn-in bead (same premise as a back stitch), thread more beads onto the needle, put your needle back up against the last sewn-in bead and pull it down through the fabric. At this point, you should see all of the sewn beads starting to form a line.

++ Stitch by stitch, continue the beaded detail. Your S.O. might look at you like you’re a psycho for wanting to bead all of those leopard spots – but it’s totally worth it! I promise. 

OTHER EMBELLISHING

++ Measure & cut enough fringe to line the edges. Sew it on by hand or with a machine.

++ Measure, cut & hand-sew any additional decorative trim, like curb chain. 

++ Finish attaching any other final details, such as light-weight studs — and BAM! There you have a beautifully glam bandana.

// PROTIPS //

++ If you choose to bead, note that beading needles and regular sewing needles are different. Beading needles are much longer and thinner in order to go through the teeny tiny seed beads – plus the world’s worst to thread. You also can’t use thicker thread with beading needles because it won’t feed through the eye, so go with one that’s thin yet durable.

++ When beading straighter designs, you can sew more beads at a time. For curvier details that need greater accuracy (i.e. our beautiful leopard spots) you have to stick with one to three beads at a time. 

++ It’s easiest to dump your beads into a shallow container and stick your needle into the pile to catch them instead of hand-threading each bead onto the needle.

++ When hand sewing any other details onto your presentation side of the bandana, also be careful not to accidentally sew the two sides together! Speaking as someone who this mistake the first time…ugh.

Infinity scarves, don’t say we didn’t warn you. Because this chic, post-summer staple is most def here to stay.

Let us know how they turn out for you!

xxAA

THE EASIEST DIY CHOKERS EVER

Does anyone else have a weird relationship with jewelry?

I mean, it’s cool. It’s classic. Almost all of the older women in your life are super into it. But there’s still just something about it that’s always been a little tricky, if you ask me.

The cheap stuff these days isn’t really all that cheap. Finding the right piece can take a lifetime. AND when it comes to traveling, it’s hard not to worry that it will all meet an unfortunate demise of pulverization in your suitcase! Regardless if it’s the TSA’s “fault” or not…

But – there’s no denying it IS a killer way to elevate almost any outfit. So that’s what has always made me want to find a way to make it work.

Enter: TRIM. Something you may or may not be familiar with, although get ready, ‘cause it’s about to become your new best friend! Mainly due to the fact it’s inexpensive, customizable AND totally manageable for any DIYer – no matter how well you do (or don’t) know your way around a needle and thread.

Amazing, right?

Another perk is that by using trim, you can design the necklace however intricate or basic you please. Break it up with additional jump rings to create a cool look – or keep it super simple yet chic and edgy with the choker alone. But either way, you can throw it around without having to think t w i c e.

Seriously! Suitcase, gym bag, purse—it’s all NO match for this mighty accessorizing hack.

So let’s jump into it!

// WHAT YOU NEED //

+ A piece of trim

+ Curb chain

+ Needle & thread

+ Your choice of closure (I use a hook & eye)

// STEPS //

++ Measure the amount of trim you need based on your neck size, leaving 1/4 to 1/2 inch extra on each end. Remember, you want it to fit like a choker without, you know, actually choking you.

++ Take one end of the trim, fold the extra section back and sew it down to create a neat, fray-free edge. If your trim has a lot of metal embellishment like mine, you’ll probably need to hand sew it; however, if you want to use a sewing machine to zig-zag stitch it instead, be my guest!

++ Repeat on the other end, then double check that the finished length still comfortably fits your neck (i.e. didn’t accidentally get shortened too much in the process).

++ Take your choice of closure and hand sew a piece to each end.

++ Figure out how you want to position the curb chain, then hand-sew each end of it onto the back of the trim (but not too close to the bottom edge or else you run the risk of it sagging).

++ Voila! Enjoy your super-cute, new favorite accessory. 

// PROTIPS //

++ Whenever hand sewing things like this, I almost always opt for button/craft or upholstery thread instead of regular all-purpose, because it has that nice extra dose of durability. 

++ I personally like to use hook & eyes for necklaces because they feel the most secure to me, but you can totally use whatever works best for you! Snaps, velcro – even a safety pin can do the trick if sewing REALLY isn’t your forte & you want to spare the band-aids. 

++ All in all, the most important thing is to keep measuring as you go, juuust to make sure it doesn’t end up being too small. If you want to be safe, always lean toward keeping the trim slightly longer than you need, since you can always stitch together a gathered section of it in the back to tighten the necklace at the very end. No one will ever see it – and your secret will always be safe with us.

Let us know how it turns out for you! 

xxAA